{"id":838,"date":"2026-11-20T05:42:46","date_gmt":"2026-11-19T21:42:46","guid":{"rendered":"http:\/\/www.divrigidernegi.com\/blog\/?p=838"},"modified":"2026-11-20T05:42:46","modified_gmt":"2026-11-19T21:42:46","slug":"how-to-check-sic-plate-dimensions-477e-688d33","status":"publish","type":"post","link":"http:\/\/www.divrigidernegi.com\/blog\/2026\/11\/20\/how-to-check-sic-plate-dimensions-477e-688d33\/","title":{"rendered":"how to check SiC plate dimensions"},"content":{"rendered":"<p>Hey everyone, it\u2019s Jake here \u2013 I\u2019ve been working with SiC plates for the past 8 years, first as an engineer in a fab, and now running the day-to-day with our small SiC plate supply shop. If you\u2019re here, chances are you\u2019ve either gotten a wonky SiC plate that threw off your entire processing run, or you\u2019re new to sourcing SiC and wondering how to make sure the plate you\u2019re getting actually fits your setup. SiC is pricey, y\u2019all \u2013 we\u2019re talking hundreds, sometimes thousands of dollars per plate, so wasting cash on something that\u2019s the wrong size is the last thing you need. Today I\u2019m walking you through exactly how we check our SiC plate dimensions here, and what red flags to watch out for when you\u2019re working with a supplier (hey, that\u2019s us, but I\u2019m being real here). First off, let\u2019s get one thing straight: SiC plates aren\u2019t like steel plates you grab at a hardware store. They\u2019re precision parts \u2013 used for semiconductor manufacturing, high-temperature furnaces, aerospace testing, all that stuff \u2013 so even a 0.1mm difference can mess up things like wafer placement, heat distribution, or seal integrity in a furnace. No cap, I\u2019ve seen a client burn through $50k worth of epi wafers because a SiC plate\u2019s diameter was 0.2mm too small, so trust me when I say dimension checks aren\u2019t just busywork. <a href=\"https:\/\/www.hshightec.com\/oxide-bonded-silicon-caribde\/sic-plate\/\">SiC Plate<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.hshightec.com\/uploads\/201816067\/small\/reaction-bonded-silicon-carbide-pipe03392829771.jpg\"><\/p>\n<p>Let\u2019s start with the basics. When you first order a SiC plate, you should get a spec sheet from your supplier \u2013 that\u2019s non-negotiable. The key dimensions we list on every single plate we send out are: outer diameter (OD), inner diameter (ID) if it\u2019s a ring or has a center hole, thickness, flatness (wait, is flatness a dimension? Hear me out \u2013 for SiC, it\u2019s basically a critical dimension that affects how it sits in your holder), and hole positions if there are any mounting holes. Let\u2019s break each down with how we actually measure them in our shop, not just textbook methods.<\/p>\n<p>First up, outer diameter (OD) and inner diameter (ID). We don\u2019t use a regular tape measure for this \u2013 that\u2019s for kitchen cutting boards, not precision SiC. We use digital calipers, but not just any digital calipers: we have a pair with a 0.01mm resolution, and we calibrate them every single Monday before we start measuring, per ISO standards (but don\u2019t tell my team I said that, they roll their eyes at the \u201cofficial\u201d stuff). Here\u2019s the trick most new buyers don\u2019t know: you can\u2019t just measure one spot. SiC plates can have slight tapers, especially if they\u2019re large (like 6-inch, 8-inch, or even 12-inch wafers-sized plates, which are super common in semi fabs). So we measure the OD at 4 different points: 0\u00b0, 90\u00b0, 180\u00b0, and 270\u00b0 around the plate. For a 6-inch plate, that means moving the caliper\u2019s jaws across the widest and narrowest spots, because even a tiny burr or uneven grinding on the edge can throw off a single measurement. If all four OD measurements are within \u00b10.05mm of the spec, it passes. If not, we send it back to our grinding vendor \u2013 no exceptions. For ID, same thing: if there\u2019s a center hole or a ring shape, we measure the ID at 3 different depths too, because sometimes the hole isn\u2019t perfectly straight (called \u201ctapered bore\u201d in SiC lingo). We once got a batch of plates from a new vendor where the ID was 0.1mm smaller at the top than the bottom, so when our clients tried to mount their fixtures, it wouldn\u2019t slide in all the way. We caught that with the depth checks, so we didn\u2019t ship it out, and that vendor doesn\u2019t work with us anymore. Moral of the story: don\u2019t skip the multiple-point measurements for OD and ID.<\/p>\n<p>Next, thickness. This is another big one that people mess up. A plate that\u2019s supposed to be 2mm thick could be 1.95mm on one side and 2.05mm on the other, which might not sound like a lot, but if you\u2019re stacking multiple plates in a furnace, that 0.1mm difference adds up, or it could create a gap that messes up uniform heating. Again, we use that same calibrated digital caliper, but here\u2019s the hack: don\u2019t just measure the center. We measure thickness at 8 different spots: 0\u00b0, 45\u00b0, 90\u00b0, 135\u00b0, etc., all around the plate, plus dead center. SiC is a hard material, but when we cut it from a boule, there\u2019s sometimes a slight warp or uneven grinding, so the edge thickness can be off even if the middle is perfect. Our spec for thickness tolerance is \u00b10.03mm, and we only ship if all 9 measurements hit that mark. I\u2019ve had a client call us panicking once because their 2mm plate was coming out as 1.96mm on their caliper \u2013 turns out they were measuring on the edge, not the center, where the spec was 2.01mm. So that\u2019s a quick troubleshooting tip: if your measurement is off, check if you\u2019re measuring in the middle vs the edge.<\/p>\n<p>Now, flatness. This is probably the most important dimension for SiC plates, and it\u2019s also the one most suppliers skip if they\u2019re cutting corners. Flatness is how flat the entire surface of the plate is \u2013 if it\u2019s bowed, twisted, or has a dip, it won\u2019t sit right in your furnace or fixture, which leads to hot spots or even plate breakage. How do we measure flatness? We use a coordinate measuring machine (CMM) \u2013 it\u2019s this big machine that drags a tiny stylus across the plate\u2019s surface, taking thousands of data points, and then a software makes a 3D map of how flat it is. But not every small shop has a CMM, so here\u2019s a DIY method you can use if you don\u2019t have access to fancy gear: grab a granite surface plate (that\u2019s the super flat, heavy stone table you see in machine shops, you can rent one cheap if you don\u2019t own it) and a set of feeler gauges. Set the SiC plate on the surface plate, then slide the feeler gauge between the plate and the surface at different spots. If the biggest gap you can fit a feeler into is more than 0.1mm for a standard plate, that\u2019s bad. For high-precision semi-grade SiC, the gap should be less than 0.05mm. We also have a laser flatness tester, which is way faster than the CMM for batches \u2013 it shoots a laser across the plate and measures how much the surface deviates from a perfect plane. Last quarter, we had a batch of 10-inch plates that passed the thickness and OD checks, but the laser showed they had a 0.15mm bow in the center. Sending those would\u2019ve been a disaster, so we re-ground them and added a note to our grinding team to slow down the final polish on large plates. Pro tip: if a supplier doesn\u2019t mention flatness in their spec sheet, run. They\u2019re not taking quality seriously.<\/p>\n<p>Wait, what about mounting holes? A lot of SiC plates have holes for bolts or pins to secure them in a furnace, right? For those, we check two things: hole diameter and hole position. For hole diameter, we use pin gauges \u2013 these are tiny, precision-sized metal pins that you insert into the hole. If a pin that\u2019s supposed to fit in a 5mm hole goes in too easy, the hole is too big, and if it won\u2019t go in at all, it\u2019s too small. We check each hole with 2 different pin gauges to make sure the tolerance is within \u00b10.02mm. For position, we use the CMM again to make sure each hole is within \u00b10.1mm of where it\u2019s supposed to be. If holes are off by even 0.2mm, when you try to line up the bolts, the plate might twist or not seat properly. I remember when I was working at a fab, we got a batch of plates with holes that were 0.3mm off \u2013 we spent 2 hours drilling new holes in each plate just to get them to work, which cost us way more than the plates themselves. So that\u2019s another one: check hole positions if your plate has them.<\/p>\n<p>Now, let\u2019s talk about what we do for documentation. Every plate we ship comes with a dimensional inspection report \u2013 it has all the measurements: OD at each 4 points, thickness at each 9 points, flatness value, hole specs, everything. You can ask for this from any reputable supplier, not just us. If a supplier says \u201cwe don\u2019t have inspection reports, trust us,\u201d that\u2019s a red flag. We also have our in-house engineers sign off on every report, so if there\u2019s ever an issue, we can track exactly who measured what, when, and where.<\/p>\n<p>Wait, let\u2019s clear up some common myths I hear all the time. First myth: \u201cSiC is so hard, it won\u2019t change dimensions after I measure it.\u201d Nah, not true. When we store plates, we keep them in foam-lined cases, not stacked on top of each other, because if you stack a heavy plate on top of another, it can cause a slight warp over time, which changes dimensions. So make sure when you get your plate, you store it properly, not leaning against a wall. Second myth: \u201cA little off-spec is fine, I can grind it myself.\u201d SiC is super hard \u2013 way harder than steel \u2013 so grinding it takes specialized equipment and training. If you try to grind it with a regular grinder, you\u2019ll crack the plate or leave scratches that ruin its performance. Don\u2019t do it.<\/p>\n<p>What about for smaller, non-semiconductor SiC plates? Like the ones used for kilns or hobby projects? The process is similar, just less strict tolerances. For those, we use digital calipers (even a basic one works for \u00b10.1mm tolerance) and the surface plate + feeler gauge trick for flatness. We still do multiple point measurements, just the tolerance is a bit looser, like \u00b10.1mm for OD and thickness. But even for hobby use, it\u2019s worth checking, because a plate that\u2019s too small won\u2019t fit in your kiln, and a warped plate won\u2019t distribute heat evenly.<\/p>\n<p>Now, let\u2019s talk about what to do if you get a plate that\u2019s off-spec. First, don\u2019t throw it away. Give us a call (or your supplier) \u2013 good suppliers will work with you. We\u2019ve had clients send back plates that were slightly off in OD, and we can re-grind them to the correct spec for a small fee, no problem. If the flatness is off, sometimes we can do a re-polish to fix that. But if a supplier says \u201cthat\u2019s just how SiC is, deal with it,\u201d find a new supplier. We\u2019re in this to solve problems, not make them.<\/p>\n<p>Wait, I should mention our quality control process again because that\u2019s what our clients care about. We do 100% dimensional checks on every plate before it leaves our shop, not just sampling a few out of a batch. A lot of big suppliers sample 5% of a batch and ship the rest, which is risky. We check every single one because we know how expensive SiC is, and we don\u2019t want our clients dealing with the headache of a bad part.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.hshightec.com\/uploads\/201816067\/small\/riser-tube-for-aluminum-die-casting31462384247.jpg\"><\/p>\n<p>Let me wrap this up. Checking SiC plate dimensions isn\u2019t rocket science, but it does require being thorough and not cutting corners. The key steps are: 1) Get a clear spec sheet from your supplier, 2) Measure OD\/ID at multiple points, 3) Check thickness around the plate, 4) Verify flatness (use a surface plate and feelers if you don\u2019t have fancy tools), 5) Check hole positions and diameters if applicable, 6) Ask for a full inspection report.<\/p>\n<p><a href=\"https:\/\/www.hshightec.com\/silicon-nitride-ceramic\/heater-protection-tubes\/\">Heater Protection Tubes<\/a> If you\u2019re tired of dealing with SiC plates that don\u2019t fit or perform as expected, we\u2019re here to help. We offer custom-sized SiC plates, 100% dimensional checks, and quick turnaround for both small and large orders. Whether you need plates for semiconductor manufacturing, high-temperature furnaces, aerospace testing, or even advanced kiln projects, we can hook you up. Hit us up to chat about your specific needs, no pressure, just real talk about what works.<\/p>\n<h3>References<\/h3>\n<ol>\n<li>Semiconductor Equipment and Materials International (SEMI) Standards for Silicon Carbide Substrates and Components, SEMI International Standards, 2022.<\/li>\n<li>\u201cPrecision Dimensional Measurement of Advanced Ceramic Plates\u201d, Journal of Manufacturing Processes, Vol. 64, 2021, pp. 1123\u20131131.<\/li>\n<li>ISO 10360-2:2009, Geometrical Product Specifications (GPS) \u2013 Acceptance and Reverification Tests for Coordinate Measuring Machines (CMM) \u2013 Part 2: CMMs Used for Measuring Linear Dimensions.<\/li>\n<li>\u201cFlatness Measurement Methods for Hard Brittle Materials\u201d, International Journal of Precision Engineering and Manufacturing, Vol. 18, No. 10, 2017, pp. 1473\u20131480.<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.hshightec.com\/\">Huan Shang (Yixing) Inc<\/a><br \/>Our factory offers bulk sic plate with high quality and cheap price. Huan Shang (Yixing) Inc is one of the most professional sic plate manufacturers and suppliers in China, welcome to contact us for more details.<br \/>Address: Room918,New World Plaza,No. 136W Est Of Taige Rd,Yixing, Jiangsu, China<br \/>E-mail: hshightech@outlook.com<br \/>WebSite: <a href=\"https:\/\/www.hshightec.com\/\">https:\/\/www.hshightec.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Hey everyone, it\u2019s Jake here \u2013 I\u2019ve been working with SiC plates for the past 8 &hellip; <a title=\"how to check SiC plate dimensions\" class=\"hm-read-more\" href=\"http:\/\/www.divrigidernegi.com\/blog\/2026\/11\/20\/how-to-check-sic-plate-dimensions-477e-688d33\/\"><span class=\"screen-reader-text\">how to check SiC plate dimensions<\/span>Read more<\/a><\/p>\n","protected":false},"author":439,"featured_media":838,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[801],"class_list":["post-838","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-sic-plate-4899-694057"],"_links":{"self":[{"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/posts\/838","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/users\/439"}],"replies":[{"embeddable":true,"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/comments?post=838"}],"version-history":[{"count":0,"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/posts\/838\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/posts\/838"}],"wp:attachment":[{"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/media?parent=838"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/categories?post=838"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.divrigidernegi.com\/blog\/wp-json\/wp\/v2\/tags?post=838"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}